ASM type 3 engine

ASM type 3 engine

  • ASM type 3 engine
  • Perform special treatment on piston and sleeve to dramatically reduce frictional resistance.
    Prevention of scratches and galling (burning) on the piston sleeve due to high speed rotation,
    Not only can it demonstrate engine performance reliably, it helps to extend the life of the engine itself.
    Also when doing BREAK IN,
    troubles easily occurred in the piston and trouble caused by galling (burning) are extremely lost.
    Even a good engine fails BREAK IN, the original performance will not be demonstrated.
    There are two BREAK IN in NUCLEAR.
    BREAK IN with bench and
    COMPLEAT BREAK IN which is actually carried on the car body is prepared.
    An engine that has been completed to 95% is being prepared.
    Using about 1 gallon of special oil blended fuel, we will complete one engine.
    In the type 3 engine, special processing was also applied to the connecting rod,
    piston pin and back plate which are also used in the type 2 engine.
    Response, etc., to maximize engine performance can be drawn.
    It also reduces the burden on piston pin and connecting rod.
    In the type 3 engine, the friction loss was reduced to the maximum extent.
  • Here is the change point of the ASM type 3 engine.

    Piston, = special treatment (select)

    Sleeve, = special treatment (select)

    Piston pin, = special treatment + machining

    Back plate, = special treatment

    Connecting rod, = special treatment


  • ASM also performs the same tuning for the following engines
  • MAX 12 TG VER Ⅲ (connecting rod, piston pin, back plate not processed)

    Piston, = special treatment (select)

    Sleeve, = special treatment (select)
  • T1202 engine (back plate not processed)

    Piston, = special treatment (select)

    Sleeve, = special treatment (select)

    Piston pin, = special treatment + machining

    Connecting rod, = special treatment
  • B2102 engine

    Piston, = special treatment (select)

    Sleeve, = special treatment (select)

    Piston pin, = special treatment + machining

    Back plate, = special treatment

    Connecting rod, = special treatment
  • 21XZ-B Spec Ⅲ engine

    Piston, = special treatment (select)

    Sleeve, = special treatment (select)

    Piston pin, = special treatment + machining

    Back plate, = special treatment

    Connecting rod, = special treatment
  • 21XZ-GT engine

    Piston, = special treatment (select)

    Sleeve, = special treatment (select)

    Piston pin, = special treatment + machining

    Back plate, = special treatment

    Connecting rod, = special treatment

Clutch shoe for 1/8 GPR

Clutch shoe for 1/8 GPR

  • Clutch shoe for 1/8GPR:
    Three types of clutch shoes, soft, medium and hard,
    You can use it according to your taste.
    New clutch shoes will never be reduced
    Also, there is little change due to heat.
    Clutch setting is easy.
    Rapid acceleration and abrupt deceleration become possible.
      TYPE NAME
    MUGEN,CAPRICORN Clutch shoe soft for 1/8GPR
    MUGEN,CAPRICORN Clutch shoe medium for 1/8GPR
    MUGEN,CAPRICORN Clutch shoe hard for 1/8GPR

ASM ENGINE 21 ON-ROAD

ASM ENGINE 21 ON-ROAD

  • About ASM Type 1 engine COMPLEAT BREAK IN:
     BREAK IN is done using ASM proprietary formulated glow fuel.
     The engine made with ASM's ultra-high refined oil can prolong the life of the engine.
     It is also possible to derive 100% of the performance of the engine.
     About 1 gallon of fuel is used and it is politely finished in actual running.
     Carburetor setting is given in advance.
     Needle adjustment can be done more easily.
  • Spec:
     Stroke volume: 3.49 cc
     Bore: 16.08 mm
     Stroke: 17.2 mm
     Practical rotation speed: 4,000 to 45,000 rpm.
     Output: 2.8 ps / 33,000 rpm (2.76 hp / 33,000 rpm).
     Weight: 340 g
  • Standard accessory:
     Standard included plug T-RP 7 / exhaust seal ring / taper collet / ASM inner head

INVINCIBLE Tire

INVINCIBLE Tire

  • Description of INVINCIBLE tire:
    ULTI INVINCIBLE tire,It is a super high grade tire.
    When the circuit condition is bad, when there are lots of dust,
    When the circuit condition is good, when there are lots of oil,
    Both good effects were obtained.
    The INVINCIBLE tire does not suddenly lose grip.
    It is easy to adsorb oil on the circuit.
    Therefore, the life of the tire can be used for a very long time.
  • Tire type:
      TIRE TYPE NAME
    Front Tires 08F-M-INVINCIBLE Front Medium (Light weight wheel)
    Front Tires 08F-M-INVINCIBLE Front Medium (Hard carbon wheel)
    Rear Tires 08R-M-INVINCIBLE Rear Medium (Light weight wheel)
    Rear Tires 08R-M-INVINCIBLE Rear Medium (Hard carbon wheel)

ULTI Traction Oil

ULTI Traction Oil

  • 01A Description of traction oil
    The function of softening the tire moderately,
    It is made for the purpose of improving the grip.
    It is not a component that extremely inflicts tires.
    Without extremely changing the original hardness of the tire,
    It is traction oil developed for the purpose of improving grip.
    We were able to realize grip securing without disrupting the front and rear tire balance.
  • Explanation of G5 traction oil:
    G5 Traction oil is an additive.
    Please add at the ratio of 01A traction oil 2 to 4 to G5 traction oil 1.
    G5 Depending on the addition rate of traction oil, further grip can be secured.

1/8 GP On-Road

1/8 GP On-road sponge tire

  • 1/8 Foam Tire for 2013 World Championship【Carbon Rims】
      LINEUP HARDNESS
    Front Tires  08F-30-2013WC 30°
    Front Tires 08F-32-2013WC 32°
    Front Tires 08F-35-2013WC 35°
    Rear Tires 08R-35-2013WC 35°
    Rear Tires  08R-37-2013WC 37°
  • 1/8 Foam Tire for 2015 【LightWeigt Rims】
      LINEUP HARDNESS
    Front Tires 08F-30-L-2015 30°
    Front Tires 08F-32-L-2015 32°
    Front Tires 08F-35-L-2015 35°
    Rear Tires 08R-35-L-2015 35°
    Rear Tires 08R-37-L-2015 37°
  • 1/8 Foam Tire 【Doughnut】※Not Rims
      LINEUP HARDNESS
    Front Tires 08F-D30 30°
    Front Tires 08F-D32 32°
    Rear Tires 08R-D35 35°

1/10 GP Touring

1/10 GP Touring sponge tire

  • 1/10 Foam Tire【Hard Rims】
      LINEUP HARDNESS
    Front Tires 10F-CMB(A)-H Combination(A)
    Front Tires 10F-35-H 35°
    Front Tires 10F-38-H 38°
    Front Tires 10F-40-H 40°
    Rear Tires 10R-38-H 38°
    Rear Tires 10R-40-H 40°
    Rear Tires 10R-42-H 42°
  • 1/10 Foam Tire【LightWeight Rims】
      LINEUP HARDNESS
    Front Tires 10F-CMB(A)-L Combination(A)
    Front Tires 10F-35-L 35°
    Front Tires 10F-38-L 38°
    Front Tires 10F-40-L 40°
    Rear Tires 10R-38-L 38°
    Rear Tires 10R-40-L 40°
    Rear Tires 10R-42-L 42°

1/12 EP Racing

1/12 EP Racing sponge tire

  • 1/12 Form Tire 【 J Compound】
    ◆1pair (2 pcs)
      LINEUP HARDNESS
    Front Tires 12F-JS J-Soft
    Front Tires 12F-JM J-Medium
    Front Tires 12F-JH J-Hard
    Rear Tires 12R-JS J-Soft
    Rear Tires 12R-JM J-Medium
  • 1/12 Form Tire 【 J Compound】
    ◆3pairs (6 pcs)
      LINEUP HARDNESS
    Front Tires 12F-6-JS J-Soft
    Front Tires 12F-6-JM J-Medium
    Front Tires 12F-6-JH J-Hard
    Rear Tires 12R-6-JS J-Soft
    Rear Tires 12R-6-JM J-Medium
  • 1/12 Form Tire 【 X Compound】
    ◆1pair (2 pcs)
      LINEUP HARDNESS
    Front Tires 12F-XS X-Soft
    Front Tires 12F-XM X-Medium
    Front Tires 12F-XH X-Hard
    Rear Tires 12R-XSS X-SuperSoft
    Rear Tires 12R-XS X-Soft
    Rear Tires 12R-XM X-Medium
    Rear Tires 12R-XH X-Hard
  • 1/12 Form Tire 【 X Compound】
    ◆3pairs (6 pcs)
      LINEUP HARDNESS
    Front Tires 12F-6-XS X-Soft
    Front Tires 12F-6-XM X-Medium
    Front Tires 12F-6-XH X-Hard
    Rear Tires 12R-6-XSS X-SuperSoft
    Rear Tires 12R-6-XS X-Soft
    Rear Tires 12R-6-XM X-Medium
    Rear Tires 12R-6-XH X-Hard
  • 1/12 Form Tire 【 Y Compound】
    ◆1pair (2 pcs)
      LINEUP HARDNESS
    Front Tires 12F-YS Y-Soft
    Front Tires  12F-YM Y-Medium
    Front Tires  12F-YH Y-Hard
    Rear Tires 12R-YS Y-Soft
    Rear Tires 12R-YM Y-Medium
  • 1/12 Form Tire 【 Y Compound】
    ◆3pairs (6 pcs)
      LINEUP HARDNESS
    Front Tires 12F-6-YS Y-Soft
    Front Tires 12F-6-YM Y-Medium
    Front Tires 12F-6-YH Y-Hard
    Rear Tires 12R-6-YS Y-Soft
    Rear Tires 12R-6-YM Y-Medium
  • 1/12 Form Tire 【 Z Compound】
    ◆1pair (2 pcs)
      LINEUP HARDNESS
    Rear Tires 12R-ZS Z-Soft
  • 1/12 Rims ※Not Forms
    ◆3pairs (6 pcs)
      LINEUP COLOR
    Front wheel 12F-6-RIM BLACK
    Rear wheel 12R-6-RIM BLACK
  • 1/12 Foam Tire 【Doughnut】※Not Rims
    ◆3pairs (6 pcs)
      LINEUP HARDNESS
    Front Tires 12F-6-DXM X-Medium
    Front Tires 12F-6-DXH X-Hard
    Rear Tires 12R-DXSS X-SuperSoft
    Rear Tires 12R-6-DXS X-Soft
    Rear Tires 12R-6-DXM X-Medium
  • 1/12 wheel adapter
    ◆3pairs (6 pcs)
      LINEUP HARDNESS
    Rear  12R-6-RAS Soft(BLACK)
    Rear  12R-6-RAM Medium(CLEAR)

J This matches asphalt to all to a carpet, and the condition of an especially high grip.
It is the standard foam used all over the world for some time.
X This matches a carpet and a low grip and matches a tire treatment well.
This foam was developed in Japan recently and showed performance by the 2012 world championship.
Z This matches asphalt to all to a carpet, and the condition of an especially low grip.
Evaluation of a top driver is a very good new foam. It is a different foam in X. It is very expensive.
Y This resembles X compound. It is easy to control. There is less wear than X compound.

ULTI T-Shirt & ULTI Sticker

ULTI T-Shirt & ULTI Sticker


LINEUP

SIZE COLOR LENGTH WIDTH
UL-TS-XS-B XS Black 60 44
UL-TS-XS-W XS White 60 44
UL-TS-S-B S Black 66 48
UL-TS-S-W S White 66 48
UL-TS-M-B M Black 72 51
UL-TS-M-W M White 72 51
UL-TS-L-B L Black 75 54
UL-TS-L-W L White 75 54
UL-TS-LL-B LL Black 77 57
UL-TS-LL-W LL White 77 57
UL-TS-3L-B 3L Black 83 60



LINEUP NAME QUANTITY
UL-ST-#901 ULTI Sticker(Size:155mm×255mm) 1 sheet